ASTM D7012 EPUB DOWNLOAD

D – 13 Standard Test Methods for Compressive Strength and Elastic Moduli of Intact Rock Core Specimens under Varying States of Stress and. All the Controls products ASTM D standard. Enter now!. 26 Nov ASTM D Method C. Reference. Uniaxial Compressive Strength of Intact Rock Core Specimens. (deg). Type. Failure Mode. Rock Type.

Author: Vutilar Douzragore
Country: Equatorial Guinea
Language: English (Spanish)
Genre: Technology
Published (Last): 2 March 2010
Pages: 257
PDF File Size: 17.77 Mb
ePub File Size: 1.99 Mb
ISBN: 326-2-81653-979-9
Downloads: 37592
Price: Free* [*Free Regsitration Required]
Uploader: Dogal

Therefore, laboratory values for intact specimens must be employed with proper judgment in engineering applications.

ASTM D, Test equipment Controls

The elastic moduli for such rocks should be determined from unload-reload cycles that are not covered astm d7012 these test methods. Method A, triaxial compression test, is commonly used to simulate the stress conditions under which most underground rock masses exist.

Methods A and B determine the triaxial compressive strength at different pressures and Methods C and D astm d7012 Link to Active This link will always route to the current Active version of the standard.

In addition, they are representative of the significant astm d7012 that generally should be retained. Referenced Documents atsm separately The documents listed below are referenced within the e7012 standard but are not provided as part of the standard. Strain is not satm measured; therefore a stress-strain curve is not produced.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are astmm provided as part of the standard. However, there are some cases where either the rock type or the loading condition of the astm d7012 under astm d7012 will require the effective stress or drained parameters be determined.

The parameters obtained from Methods A and B awtm in terms of undrained total stress as already mentioned in 1. It is the responsibility of the astm d7012 of this standard to establish appropriate safety and health adtm astm d7012 determine the applicability of regulatory limitations prior to use.

You may also like -  ANTIGUEDADES JUDIAS FLAVIO JOSEFO PDF

Related Products Searching for related products Deformation and strength of rock are known to be astm d7012 of confining pressure. Elastic moduli measured by sonic methods Test Method D may often be employed as a preliminary measure of anisotropy.

The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used.

Astm d7012 is the responsibility of the user of this standard to establish astm d7012 safety and health practices and determine the applicability of regulatory astm d7012 prior to use. Thus, the strength values determined are in terms of total stress and are not corrected for pore pressures. It is desirable to conduct tests in the plane of foliation, cleavage or bedding astm d7012 at right angles s7012 it to determine the degree of anisotropy.

Method A, triaxial compression test, is commonly qstm to simulate the stress conditions under which most underground rock masses exist.

This guide is primarily for use in coring through shallow 0. Astm d7012 option is identified by astm d7012 Certificate code shown on the x7012 table. Users of this standard are cautioned that compliance with Practice D does not in itself ensure reliable results. It is beyond the scope of this standard to consider significant digits used in analytical methods for engineering design.

ASTM International

These test methods astm d7012 not include the procedures necessary to obtain a stress-strain curve asgm the ultimate strength. It is beyond the scope of this standard to consider significant digits used in analytical methods for engineering design.

Active view current version of standard. When required, the hardness verification is performed with certified instruments. Thus, the strength values determined are in terms of total stress and are not corrected for pore pressures. It is desirable to conduct tests in astm d7012 plane of foliation, cleavage or bedding and at right angles asm it to determine the degree astm d7012 anisotropy.

You may also like -  A PROFECIA CELESTINA PDF

The astm d7012 constants Methods B and D are used to calculate the stress and deformation in rock structures.

Home Products Search results Results for: Therefore, the dynamic elastic p Follow us YouTube Astm d7012. Related Suppliers Searching for related suppliers No other units of measurement are included in this standard.

These test methods do astm d7012 include the procedures necessary to obtain a stress-strain curve beyond the ultimate strength. The elastic moduli for such rocks should be determined from unload-reload cycles, that are not covered by this test method.

No other astm d7012 of measurement ast, included in this standard. No other units of measurement are included in this standard. It is applicable to nuclides emitting gamma rays with energies greater than 20 keV. In addition, they are representative of the significant digits that generally should be retained. Referenced Documents purchase ast, The documents listed below are referenced within the ast, standard but are not provided as part of astm d7012 standard. Methods A and B determine the triaxial compressive strength at different pressures and Methods C and D determine the unconfined, uniaxial strength.

The elastic moduli for such rocks should be determined from unload-reload cycles that are not covered by these test astm d7012. The tests provide data in determining the strength of rock, namely:

Begin typing your search term above and press enter to search. Press ESC to cancel.

Back To Top